Air duct cleaning means removing dust and debris from the ducts that carry air from your system to the rooms of your home and back. In Texas, the scope of a normal duct cleaning visit is set by a state rule, so it helps to know that rule before you compare companies.
The scope Texas allows without a contractor license
16 TAC §75.100(c)(1) lets a person or company clean ducts without the state air conditioning and refrigeration contractor license when all four of these are true:
- The task is limited to the air distribution system: from the supply plenum to the supply grilles, and from the return air grille to the air handler intake.
- No cuts are made to ducts or plenums.
- No changes are made to electrical connections.
- The only disassembly is opening or removing return and supply grilles or registers that come off without cutting or removing any other part of the system.
Read together, that describes the ducts and the grilles and registers on them. It stops at the plenums and at the air handler. If a company proposes to go further, for example to cut access holes into a duct, the work is outside this exemption, and you should ask for the company's state license number and check it on the TDLR license search.
National guidance is written for the whole country and sometimes describes a wider job. EPA's consumer guide, for example, says a provider should open access ports or doors so the entire system can be cleaned and inspected. (EPA) In Texas, who may do that depends on the rule above, so ask before work starts.
What a careful duct cleaning looks like
EPA's guide lists what you should expect from a duct cleaning provider. The points that apply to work inside the ducts are:
- Inspect first. The provider should check for asbestos-containing materials, such as old insulation or register boots, before cleaning. EPA says those materials should be disturbed or removed only by specially trained and equipped contractors. Only about 11% of Round Rock's housing units were built before 1980 (ACS 2024 5-year), but it is still a fair question for an older home.
- Contain the dust. Vacuum equipment should exhaust outside the home, or, if it exhausts inside, it should be HEPA equipment.
- Protect the house. Carpets and furnishings should be covered.
- Brush and vacuum together. EPA describes well-controlled brushing of duct surfaces combined with contact vacuuming to dislodge and collect dust.
- Be gentle with fiberglass. Ducts made of fiberglass duct board, or sheet metal lined inside with fiberglass, should be cleaned only with soft-bristled brushes. Flexible duct can be brushed too.
- Follow the industry standards. EPA points to the standards of the National Air Duct Cleaners Association (NADCA) and, for fiberglass ducts, the recommendations of the North American Insulation Manufacturers Association.
EPA also warns that a poor job can make things worse. An inadequate vacuum collection system can release more dust than leaving the ducts alone, and a careless provider can damage ducts. (EPA) No water should be involved: EPA says steam cleaning and other methods that use moisture should not be used on any kind of ductwork.
How long it takes
There is no fixed time. NADCA says the time depends on the size of the home, the number of systems, how easy the ducts are to reach, how dirty they are, and how many technicians are on the job, and that a qualified company should be able to give a general estimate once it understands your home. (NADCA, Cost and Time Estimates) If a company charges by the hour, EPA suggests asking for an estimate of the hours or days and whether the work will be interrupted.
Checking the job afterward
EPA says a thorough visual inspection is the best way to verify cleanliness, and that you should not be able to see debris with the naked eye. Some companies photograph or video the inside of ducts before and after. For the duct part of the job, EPA's post-cleaning checklist asks:
- Are interior duct surfaces free of visible debris? Check several spots at random on both the supply and return side.
- Is fiberglass material in good condition, without tears or abrasions, and still well attached?
- Have all registers, grilles and diffusers been firmly reattached, and are they visibly clean?
- Does the system run normally after the cleaning?
Show the checklist to the company before work starts, so both sides agree what "done" means. (EPA, Post-Cleaning Consumer Checklist)
Keeping ducts clean after the visit
EPA's prevention list is mostly free: use the filter efficiency your system's manufacturer recommends, change filters regularly and more often if they clog, make sure no filter is missing and air cannot slip around it, and vacuum your home regularly. During renovation, EPA says to seal supply and return registers and not to run the system until the dust is cleaned up. That last point matters in a city where about 28% of homes were built in 2010 or later and remodeling is common.
Frequently asked questions
What does air duct cleaning include in Texas?
Under 16 TAC §75.100(c)(1), duct cleaning done without a state contractor license is limited to the air distribution system, from the supply plenum to the supply grilles and from the return grille to the air handler intake, with no cuts, no electrical changes, and only removable grilles and registers taken off.
Can a duct cleaner cut access holes in my ducts?
Not under the duct cleaning exemption, which says no cuts may be made to ducts or plenums. If a company wants to cut into the system, ask for its state license and check it on the TDLR license search before agreeing.
Should a duct cleaner use steam or water?
No. EPA says steam cleaning and other methods involving moisture should not be used on any kind of ductwork, because moisture can lead to mold growth.
How do I know the ducts were really cleaned?
Look. EPA says all cleaned surfaces should be visibly clean, and you can ask to see inside the ducts at random spots on both the supply and return side. Before-and-after photos help, but your own look at a few registers is the simplest check.