"We found mold in your ducts" is one of the most expensive sentences in duct cleaning. Sometimes it is true. This page covers how to check the claim, where Texas mold law draws its lines, and what EPA says about the chemical add-ons that often follow.
Is it really mold?
EPA says that although a substance may look like mold, only an expert can positively identify it, and lab analysis may be needed. It notes that for about $50, some microbiology labs can tell you whether a sample on clear sticky tape is mold. (EPA) Many parts of a system cannot be seen easily, so EPA advises asking the company to show you any mold it says exists.
EPA also warns about one sales tactic: showing you a settling plate (a petri dish) with growth on it. Some microorganisms are always in the air, EPA says, so some growth on a plate is normal, and using it to prove your ducts are contaminated is inappropriate.
Why the mold came back
Mold needs moisture. EPA says controlling moisture is the most effective way to prevent biological growth in air ducts, and that if the conditions that caused mold are not corrected, it will recur. EPA points to condensation on or near the cooling coil as a major source of moisture in systems, and to ducts that are not properly sealed and insulated where they pass through spaces that are not air-conditioned, such as attics. Both are worth asking about. A duct cleaning by itself does not fix them.
Wet or moldy insulated ducts
EPA says that if insulated ducts get wet or moldy, the insulation cannot be effectively cleaned and should be removed and replaced, and that EPA, NADCA and the insulation manufacturers' association all recommend replacing wet or moldy fiberglass duct material. Replacing ducts is not duct cleaning. In Texas it goes beyond the duct cleaning exemption in 16 TAC §75.100(c)(1), which allows no cuts and no disassembly beyond removable grilles and registers. Ask whoever proposes it for a state license number and check it on the TDLR license search.
Texas mold licensing in brief
Texas regulates mold assessment and mold remediation under Occupations Code Chapter 1958, administered by the Texas Department of Licensing and Regulation (TDLR). The parts most relevant to a homeowner:
- A person does not need a mold license to remediate an area where the mold contamination affects a total surface area of less than 25 contiguous square feet. (§1958.102(c))
- An owner, or an owner's managing agent or employee, does not need a license for mold assessment or remediation on a residential property the owner owns with fewer than 10 dwelling units, unless the agent or employee is in the business of doing mold work for the public. (§1958.102(e))
- If a company working under the small-area exemption finds that the mold reaches 25 contiguous square feet or more, TDLR's rule says it must stop work and tell you that further remediation must be done by a licensed or registered person. (16 TAC §78.30(d))
TDLR's Consumer Mold Information Sheet explains these rules in plain language and says that when mold cleanup is necessary, a licensed mold assessment consultant can provide a remediation protocol. You can check a mold license on the same TDLR license search.
Sanitizers, biocides and "fogging"
Companies may offer to spray a chemical biocide into ducts to kill bacteria and mold. EPA's points:
- Biocides are pesticides under federal law. A product must be registered by EPA for a specific use, and using it in a way inconsistent with its label is a violation of federal law.
- A small number of products are registered for use inside bare sheet metal ducts. No products are registered as biocides for fiberglass duct board or fiberglass-lined ducts, so find out what your ducts are made of first.
- Little research shows that most biocides work when used inside ducts, and spraying them into an operating system can spread the material through the home. Some people react badly to them.
Before agreeing, EPA says the company should show you visible evidence of growth, explain why it cannot be removed by brushing and fixing the moisture, show you the product label, and apply it only to uninsulated areas after cleaning, strictly by the label. EPA suggests you may want to leave the home while it is applied.
Ozone
Some companies offer to send ozone through the ducts. EPA notes that ozone is a highly reactive gas regulated outdoors as a lung irritant, and that there is considerable controversy over introducing it into ductwork. (EPA) EPA has a separate page on ozone generators sold as air cleaners.
Duct sealants and coatings
Some products are sprayed inside ducts to coat surfaces and hold dust in place. EPA says lab tests indicate that materials sprayed in this way tend not to coat the duct surface completely, that sealants may affect the noise and fire-retarding properties of fiberglass ducts and may void the manufacturer's warranty, and that questions about their safety and effectiveness remain.
Frequently asked questions
How can I tell if there is mold in my air ducts?
Ask the company to show you the growth, not a petri dish. EPA says only an expert can confirm mold, sometimes with lab analysis, and that some labs test a tape sample for about $50.
Do I need a licensed mold company in Texas?
Not for every job. Under Texas Occupations Code §1958.102, mold remediation affecting less than 25 contiguous square feet does not require a mold license, and homeowners can do mold work on their own residential property with fewer than 10 units. Larger projects done for others require TDLR licensing.
Should I let a duct cleaner spray a sanitizer?
Only with visible evidence of growth and a product registered by EPA for that use. EPA says no biocides are registered for fiberglass duct board or fiberglass-lined ducts.
Do duct sealants stop dust?
EPA says lab tests show sprayed-in sealants tend not to fully coat duct surfaces, and that questions about their safety and effectiveness remain.